Booting Netra

I don't know why I have some much trouble with such a simple task, but here it goes.

Netras configured to boot off the disk and if it fails tries to boot from the net. This works fine for net booting netra into Solaris installer, but after install is done you must reset it to boot from disk. There is an option during installer to modify eeprom

#.<enter>   to get to lom
~.<enter>   to get off from console
lom>console to get to console

lom>poweroff
lom>bootmode
bootmode                normal
lom>reset

ok probe-ide
ok wprobe
ok probe-all
Probing /pci@1f,0 Device 7
Probing /pci@1f,0 Device 3
Probing /pci@1f,0 Device c  ethernet
Probing /pci@1f,0 Device 5  ethernet
Probing /pci@1f,0 Device a  usb
Probing /pci@1f,0 Device d  ide disk cdrom
todm5819
ok probe
Probing /Fast Data Access MMU Miss
ok probe-all-ide
probe-all-ide ?
ok probe-all
Probing /pci@1f,0 Device 7
Probing /pci@1f,0 Device 3
Probing /pci@1f,0 Device c  ethernet
Probing /pci@1f,0 Device 5  ethernet
Probing /pci@1f,0 Device a  usb
Probing /pci@1f,0 Device d  ide disk cdrom
todm5819
ok boot disk
Fast Data Access MMU Miss
ok boot disk0
Fast Data Access MMU Miss
ok boot disk1
Fast Data Access MMU Miss
ok boot disk:
Fast Data Access MMU Miss
ok boot disk:0
Fast Data Access MMU Miss
ok boot disk0:0
Fast Data Access MMU Miss
ok printenv auto-boot
Unknown option: auto-boot
ok printenv auto-boot?
auto-boot? =          false
ok print-env boot-device
print-env ?
ok printenv boot-device
boot-device =         disk disk0
ok setenv boot-device disk0 net
boot-device =         disk0 net
ok boot
Fast Data Access MMU Miss
ok init 0
ok boot
Fast Data Access MMU Miss
ok init 0
ok probe-all
Probing /pci@1f,0 Device 7
Probing /pci@1f,0 Device 3
Probing /pci@1f,0 Device c  ethernet
Probing /pci@1f,0 Device 5  ethernet
Probing /pci@1f,0 Device a  usb
Probing /pci@1f,0 Device d  ide disk cdrom
todm5819
ok probe-ide-all
/pci@1f,0/ide@d
  Device 0  ( Primary Master )
          ATA Model: ST340016A

  Device 1  ( Primary Slave )
         Not Present

  Device 2  ( Secondary Master )
          ATA Model: ST340016A

  Device 3  ( Secondary Slave )
         Not Present

ok printenv boot-device
boot-device =         disk0 net
ok set-defaults
Setting NVRAM parameters to default values.
ok setenv boot-device disk net
boot-device =         disk net
ok reset-all
Reset
LOM event: +3d+19h56m45s host reset
ting ...


Sun Netra X1 (UltraSPARC-IIe 500MHz), No Keyboard
OpenBoot 4.0, 1536 MB memory installed, Serial #xxxxxx.
Ethernet address x:x:x:x:x:x, Host ID: xxxxxxxxxx.

Boot device: disk  File and args:
SunOS Release 5.9 Version Generic 64-bit
Copyright 1983-2002 Sun Microsystems, Inc.  All rights reserved.
Use is subject to license terms.

Booting Netra

See Also